Pengaruh Pembesaran Dimensi Pile Terhadap  Kekuatan Struktur Pile Slab

Eko Walujodjati Walujodjati; Zulfikar Cholik

doi:10.31849/siklus.v8i2.10720

Eko Walujodjati Walujodjati institut teknologi garut
Zulfikar Cholik Program Studi Teknik Sipil, Jurusan Teknik Sipil dan Perencanaan, Institut Teknologi Garut

DOI: https://doi.org/10.31849/siklus.v8i2.10720

Keywords: displacement/deflection, moment, dimension enlargement, pile slab

Abstract

The Kapalbetung Toll Road or KAPB (Kayu Agung-Palembang-Betung) has a Pile Slab design on soft ground. Handling by improving the embankment soil, using a vacuum or stone column method is unsuitable for existing soil conditions that are waterlogged throughout the year. Initial Spun Pile D-60 cm resulted in displacement/deflection and moment capacity that did not meet the requirements. Structural reinforcement was needed to overcome the excessive displacement and minimize the Ultimate Moment on the piles. Alternatives for handling structures such as backfilling, concrete bracing, or steel bracing are considered to have extraordinary consequences. This study aims to find other alternatives in overcoming these problems. Through structural analysis by increasing the dimensions of the Spun Pile (piles) which are engineered to meet the provisions contained in the toll road planning. Enlargement of the cross-section of the piles from spun pile D-60 cm to spun pile D-120 cm, produces displacement and moment values that meet the requirements. With an increase in the dimensions of the diameter of the spun pile by 100%, the displacement decreases by 72% and when the moment meets the requirements for the maximum limit of the moment capacity of the spun pile according to the manufacturer's brochure

Downloads

Download data is not yet available.

References

Badan Standardisasi Nasional. (2016). Pembebanan untuk Jembatan. Badan Standarisasi Nasional.
Brown, D. A., Reese, L. C., & O’Neill, M. W. (1987). Cyclic lateral loading of a large-scale pile group. Journal of Geotechnical Engineering, 113(11). https://doi.org/10.1061/(ASCE)0733-9410(1987)113:11(1326)
Kurniadi, A., Rosyidin, I. F., Indarto, H., & Atmono, I. D. (2015). Desain Struktur Slab on Pile. Jurnal Karya Teknik Sipil, 4(4).
Lestari, L. L., Propika, J., & Puspasari, A. D. (2020). Axial Bearing Capacity Analysis of Pile Foundation using Nakazawa Method. Jurnal IPTEK, 24(1). https://doi.org/10.31284/j.iptek.2020.v24i1.900
Munir, M., & Yakin, Y. A. (2018). Evaluasi Deformasi dan Stabilitas Struktur Tiang Pelat (Pile Slab) di Atas Tanah Gambut (Studi Kasus: Ruas Jalan Tol Pematang Panggang - Kayu Agung, Provinsi Sumatera Selatan) (Hal. 105-116). RekaRacana: Jurnal Teknil Sipil, 4(3). https://doi.org/10.26760/rekaracana.v4i3.105
Setiyarto, D. (2017). Standar Pembebanan Pada Jembatan Menurut SNI 1725 2016. The Loading Standards on Bridges According to SNI 1725 2016.
SNI 1725:2016 Indonesia, S. N., & Nasional, B. S. (2016). Pembebanan untuk jembatan.
Wibawa, G. A. (2005). EFISIENSI PERENCANAAN JEMBATAN PILE SLAB DENGAN BENTANG BERVARIASI (Studi Kasus: Jalan Tol Nusa Dua-Ngurah Rai-Benoa). 54–62.
Yang, Y., Yu, C., Wu, Z. X., & Tu, D. M. (2020). Mitigating the Bridge End Bump Problem: A Case Study of a New Slab System with a Lower Partition Slab-Pile Foundation. Advances in Civil Engineering, 2020. https://doi.org/10.1155/2020/7986927
Zhang, D., Zhang, Y., Kim, C. W., Meng, Y., Garg, A., Garg, A., & Fang, K. (2018). Effectiveness of CFG pile-slab structure on soft soil for supporting high-speed railway embankment. Soils and Foundations, 58(6), 1458–1475. https://doi.org/10.1016/J.SANDF.2018.08.007